Congrats on being referred to CourseCareers! Find your next career path now with no upfront cost.
100% Scholarships Available. Open to Everyone.
See Scholarship Details
There is no single national UA plumbing apprenticeship aptitude test. The United Association (UA) says only that applying "may include an interview, aptitude test and physical requirements," and each local's joint apprenticeship committee picks its own test. In the local notices we read in November 2026, the tests named were a math exam, ACT WorkKeys, Accuplacer and the Bennett Mechanical Comprehension Test (plus Wonderlic Basic Skills in one local's 2025 notice), and cutoffs differ by local.
This guide lists what seven named UA locals publish about their test, minimum requirements, interviews and application windows, then compares the non-union route and gives free ways to prepare. Every test detail comes from a local's notice, a state labor department page or a trades council page we read this month, dated where the page is older.
We make the CourseCareers Plumbing course and the free Career Potential Test (CPT), so we are not neutral. Neither one is a UA test, and we say plainly below where they help and where they don't.
Key takeaways
Get ready for a plumbing apprenticeship
Our free introduction to the Plumbing course shows what the trade involves before you apply to a local.
Start the free introductionWhat's on this page
No. UA's apprenticeship pages describe the general path: applicants "must typically be at least 18 years old," should have a high school diploma or GED, and go through an application that "may include an interview, aptitude test and physical requirements." The test itself is chosen by each local's joint apprenticeship and training committee (JATC), so two locals a few hours apart can use completely different exams.
Here is what seven UA locals published about their entrance test when we read their pages in November 2026.
| UA local | Test named on its page | Cutoff stated | Where we read it |
|---|---|---|---|
| Local 13, Rochester, NY | Math exam (publisher not named) | 70% or higher | NY Department of Labor notice, March 2026 |
| Local 7, Latham, NY | Wonderlic Basic Skills (its 2025 notice; that recruitment period ended Sept. 30, 2026) | 50 or higher to be interviewed | NY Department of Labor notice, Sept 2025 |
| Local 773, Queensbury, NY | ACT WorkKeys Assessments | Average of at least 4.334 out of 7 to be interviewed | NY Department of Labor notice, Dec 2025 |
| Local 81, Syracuse, NY | Bennett Mechanical Comprehension Test | "Take and pass" (no score published) | NY Department of Labor notice, April 2026 |
| Local 34, St. Paul, MN | Accuplacer | 248 reading, 250 math | Minnesota Department of Labor and Industry, updated Oct. 2026 |
| Local 32, Seattle, WA | College entrance assessment plus a hands-on test | Placement into Intermediate Math (90 level) | Washington L&I apprenticeship standards, approved April 2024 |
| Local 162, Dayton, OH | "Pre-employment test" | Not published on the page | Columbus building trades council page |
The pattern is clear: math shows up almost everywhere, reading appears often, and at least one local uses a mechanical reasoning test. If you are also weighing electrical work, our IBEW aptitude test guide shows how the electrical side handles its entrance test.
It depends on which test your local uses, and most notices name the test without listing its contents. Here is what the pages we read actually say, grouped by test type.
Local 13 in Rochester asks applicants to "pass a Math exam at application" with a score of 70% or higher. Applicants who apply online must take it on the first Tuesday of the following month, or the application is discarded and they must reapply and pay the fee again. The notice does not say which topics the exam includes.
Local 34 in St. Paul uses Accuplacer, a college placement test, and sets minimums of 248 in reading and 250 in math. Testing happens at Saint Paul College, the exam fee is $25, a retake is $5 and three attempts are allowed. Seattle's Local 32 program, in its standards approved April 2024, asks for a Washington community or technical college assessment that places the applicant into Intermediate Math at the 90 level or higher. A "B" or better in a high school or college algebra course within the last 12 months can stand in for it.
Local 773 uses ACT's WorkKeys and asks for an average of at least 4.334 out of 7. The notice does not say which WorkKeys assessments are given. ACT's preparation page mentions practice tests for Applied Math, Graphic Literacy and Workplace Documents. Local 7's 2025 notice used the Wonderlic Basic Skills test with a cutoff of 50 and listed no subjects.
Local 81 in Syracuse requires applicants to "take and pass the Bennett Mechanical Comprehension Test." No passing score is published. Questions of this kind deal with how everyday machines and forces behave, which our mechanical aptitude test guide explains with sample concepts.
The Seattle program also gives a "Hands-on Test," and only applicants who complete it move on to the interview. The standards document does not describe the task or how it is scored.
Requirements overlap more than tests do. Across the locals we read, expect most of the following:
Gather your transcript and driver's record before the window opens. Missing paperwork is an easy way to lose a year.
Passing the test usually earns an interview, not a job. Local 773's notice (and Local 7's 2025 notice) say plainly that only applicants who reach the cutoff are interviewed. Seattle's Local 32 standards (approved April 2024) are the most detailed about what happens next: "Interview scores will become the applicants ranking score," and the committee selects apprentices "in descending order of ranking." Missing an interview keeps your hands-on score but drops you to the bottom of the list, and missing two in a row removes you from the pool.
How often locals take applications varies widely:
Because windows are short at some locals, check your local's page or your state's apprenticeship notices a few months ahead. For what contractors weigh once you are in the door, see what plumbing employers look for in apprentices.
Non-union programs run by contractor associations often work the other way around: you get hired by a member contractor first, then enroll in classes. Here is how the programs we read compare with a typical UA local.
| Route | How you get in | Entrance test stated | Source |
|---|---|---|---|
| UA local JATC | Apply to the local's committee, test, interview, get ranked | Varies by local (see table above) | Local notices and state pages |
| PHCC of Louisiana | Must already work for a PHCCLA member firm | "Essential skills test" at 70% or higher | PHCCLA apprenticeship site |
| ABC Southern California (plumbing) | Apply, wait list, test, oral interview, orientation, then dispatch to a contractor | TABE (reading, language, math computation, applied math) at 70%, two tries; interview at 80% | ABC SoCal application |
| PHCC Academy (online classes) | A participating employer sponsors you and tracks your hours | None mentioned | PHCC Educational Foundation |
A few details stand out. PHCC of Louisiana accepts applicants at 16 and calls a diploma or GED "recommended, but not required." ABC Southern California asks for one year of high school algebra or a semester of college algebra on a sealed transcript, and describes its schooling as free. PHCC Academy is a classroom option, not a full program: each online course equals 156 hours of instruction, and on-the-job training "must be coordinated with a participating employer."
Our plumbing licenses vs apprenticeship training post covers how the paths differ after you are in.
Start by finding out which test your local uses. Read its notice, its website or your state's apprenticeship listings, and call the training coordinator if the page doesn't say. Then match your prep to that test.
Example plan (an illustration, not a requirement): four weeks of algebra review at 30 minutes a day, then two weeks of timed practice tests and reading drills, for six weeks in total before your test date.
Our Plumbing course is online and self-paced (the site shows 4 to 12 weeks). It is built to help you land a first apprenticeship or entry-level plumbing job. After a free introduction, it costs $499 one time or four payments of $150.
Be clear about the limits. Our course is not accredited. It does not replace a UA apprenticeship, the on-the-job hours your state counts toward a license, or trade school where your state requires hours. It also won't get you past a local's entrance test for you; you still take that test.
The free Career Potential Test is our own test of critical thinking, reading, writing and math: 55 questions, up to an hour, webcam-proctored, with a percentile score and free retakes. No UA local we read accepts it in place of its own exam. Where it can help is with contractors who hire helpers directly, since a shareable score gives them a quick look at your math and reading. Some will consider it, and others won't. The CPT is new and we haven't published validation studies, so treat it as one signal.
Plumbing is worth the effort: the median annual wage for plumbers, pipefitters and steamfitters was $63,800 (May 2025, BLS).
Our recommendation: find your local's test first, prepare for that exact test with free official practice, and apply in the next window. If you want a head start on the trade itself or plan to approach non-union shops, take our free Plumbing introduction and the CPT alongside your prep.
What test do plumbers unions use for apprenticeships?
Each UA local picks its own. The local notices we read named a math exam, ACT WorkKeys, Accuplacer, the Bennett Mechanical Comprehension Test or, in one 2025 notice, Wonderlic Basic Skills.
What score do you need on the UA plumbing apprenticeship test?
It depends on the local. Local 13 in Rochester, NY requires 70% on its math exam, Local 773 requires a WorkKeys average of 4.334 out of 7, and Local 34 in St. Paul requires Accuplacer scores of 248 in reading and 250 in math.
How old do you have to be to join a UA plumbing apprenticeship?
Usually 18. Local 81 in Syracuse, NY accepts applicants at 17.
Can you retake a plumbers union aptitude test?
Some locals allow it. Local 34 in St. Paul allows up to three attempts with a $5 retake fee; check your own local's rules because many notices don't say.
How long is a UA plumbing apprenticeship?
UA says its apprenticeships typically last five years. Its apprentice page lists 2,000 hours of on-the-job training per year and 216 hours of related classroom instruction.
Does the Career Potential Test count for a UA apprenticeship?
No. None of the UA locals we read accepts it in place of their own test, though a contractor hiring helpers directly may choose to look at it.
See your math and reading score for free
The Career Potential Test takes up to an hour, shows a percentile right away and can be retaken as often as you like.
Take the free CPT