HVAC Apprenticeship Test: What UA, Sheet Metal and Contractor Programs Ask

HVAC Apprenticeship Test: What UA, Sheet Metal and Contractor Programs Ask

The HVAC apprenticeship test you face depends on who runs the program. Most of the union pipe trades (UA) locals and sheet metal training programs we read give an entrance test, often with a published cutoff. Some contractor association programs work differently: ABC Virginia's HVAC-R program lists no entrance test and instead requires you to already work for a licensed HVAC-R contractor. As of November 2026, named programs used tests ranging from a 15-minute math test to Criteria's cognitive aptitude test and the Bennett Mechanical Comprehension Test.

Below we lay out, program by program, what each one says it tests, the minimum requirements, how selection works, and how to prepare without paying for a prep course. Every detail comes from the program's own page or a government apprenticeship page we read this month, dated where the page is older.

A note on who is writing: we make the CourseCareers HVAC course and the free Career Potential Test (CPT). That gives us a stake in this topic, so we stick to what each program publishes and say where our products don't help.

Key takeaways

  • There is no national HVAC apprenticeship test; each union local, training center or contractor program sets its own.
  • Southern California's sheet metal JATC gives a 15-minute math test and a three-part written test needing 35 of 45 points.
  • Sheet Metal Workers Local 83 near Albany, NY uses the Criteria Basic Skills Test and CCAT, with a minimum of 6 out of 15 combined points.
  • The New York UA locals we read recruit HVAC mechanic apprentices under the same notice and test as plumbers, such as a 70% math exam at Local 13.
  • ABC Virginia's HVAC-R program lists no entrance test but requires a job in the field and charges $2,050 to $2,450 tuition.
  • HVAC mechanics and installers earned a median of $61,010 a year (May 2025, BLS).

Learn HVAC basics before you apply

Try our free introduction to the HVAC course and see how the trade works before your test or interview.

Try the free HVAC introduction

What's on this page

Is there a standard HVAC apprenticeship aptitude test?

No. HVAC apprentices come in through at least three doors, and each one screens differently: UA pipe trades locals (which train HVACR service technicians alongside plumbers and pipefitters), sheet metal workers locals affiliated with SMART (which build, install and service ductwork and air systems), and non-union programs run by contractor groups such as Associated Builders and Contractors (ABC). Here is what union programs published about their entrance test in November 2026.

ProgramHVAC track namedEntrance test on its pageCutoff stated
UA Local 13, Rochester, NYHVAC Mechanic (12 openings)Math exam70% or higher
UA Local 773, Queensbury, NYHVAC Mechanic (1 opening)ACT WorkKeysAverage of 4.334 out of 7
UA Local 81, Syracuse, NYHVAC Mechanic (4 openings)Bennett Mechanical Comprehension TestPass (score not given)
UA Local 32, Seattle, WAHVAC-Service Controls Technician / Refrigeration MechanicCollege math placement plus a hands-on testIntermediate Math, 90 level
Sheet Metal Workers Local 83, Clifton Park, NYSheet Metal WorkerCriteria Basic Skills Test and CCAT6 of 15 combined points
Southern California Sheet Metal JATC (Local 105)Sheet metalMath test plus three-part written test8th-grade math level; 35 of 45 points
Sheet Metal Workers Local 10, MinnesotaSheet metal, including residential heating and ACAptitude test (not named)Not published
Sheet Metal Workers Local 46, Rochester, NYHVAC Mechanic (10 openings)None named in the noticeAlgebra or 55 on GED/TASC math

Two things jump out. First, the UA locals we read put plumbing and HVAC applicants through the same screen, so the UA plumbing apprenticeship test guide applies to UA HVACR applicants too. Second, the sheet metal programs that describe their tests (Southern California and Local 10) lean harder on spatial and mechanical reasoning. Seattle's Local 32 details come from its standards approved April 2024.

What do HVAC apprenticeship tests cover?

Only a few programs describe their test's content, so here is exactly what the published pages say.

Southern California Sheet Metal JATC

This page is the most detailed we found. Applicants take a fifteen-minute timed math test running from "simple counting (pre-school) to intermediate algebra," and must pass at the eighth-grade level or above. A written test follows with three parts: a Mental Ability Test (abstract thinking and reasoning), a Comprehension Test (mechanical relationships and physical situations) and a Paper Board Test (picturing objects in three dimensions, the skill behind reading blueprints). Applicants need at least 35 of the 45 available points before they are invited to an oral interview.

Sheet Metal Workers Local 10 (Minnesota)

Its test is "designed to determine competence in mechanical aptitude, mathematics, and reading comprehension." The page does not name the test or give a passing score.

Sheet Metal Workers Local 83 (Capital District, NY)

Local 83 names two Criteria Corp tests, the Criteria Basic Skills Test (CBST) and the Criteria Cognitive Aptitude Test (CCAT). Applicants must score at least 6 of a combined 15 points to be considered. The notice does not describe what each test contains.

UA locals

The UA notices name a test and a cutoff but rarely the topics. Local 81's Bennett test is a mechanical comprehension exam; Local 13's is described only as a math exam; Local 773 uses WorkKeys without saying which assessments.

Employer-run tests

Contractors that hire directly may test too. Criteria Corp's own page on hiring HVAC mechanics recommends its Wiesen Test of Mechanical Aptitude, a Workplace Productivity Profile (a behavioral risk assessment covering reliability and attitudes toward rules) and, for customer-facing roles, a Customer Service Aptitude Profile. Others may not test at all, so read each job posting for what it asks.

What do you need to qualify for an HVAC apprenticeship?

Programs differ on the test but agree on most basics. Expect these, with the program that states each one:

  • Age 18 at nearly every union program we read. Southern California's sheet metal JATC says there is no maximum age.
  • A diploma or GED. The Southern California sheet metal page calls it recommended but not required.
  • An algebra record. Sheet Metal Workers Local 46 wants one year of algebra or a 55 on the GED or TASC math test. Local 83 asks for a passing algebra grade or 500 on TASC math. Oregon's Area I HVAC JATC (standards revised January 2023) asks for a C or better in a year of algebra, or equivalent placement scores.
  • Physical ability. Local 46 lists climbing, heights and lifting over 70 pounds.
  • A driving record. Seattle's Local 32 standards (approved April 2024) ask HVAC applicants for a Washington driving abstract showing no accidents or violations in the last five years, on top of a valid license.
  • Residency inside the local's area at several NY locals, for example at least one year for Local 46.
  • A job first, at some programs. A Minnesota Department of Labor and Industry page (updated Oct. 2024) says acceptance at the Metro Area Sheet Metal Workers program "is dependent on employment with a contractor," and that Central Minnesota applicants "must first seek employment with a signatory contractor."

If your algebra grade is weak or old, fix that first. It shows up as a paper requirement at many of the programs we read.

How do union, ABC and employer-hire HVAC routes compare?

Union programs screen you, rank you and then dispatch you to a contractor. Contractor association programs usually start after a company has already hired you. This table compares the routes using programs we read.

RouteExample programTest before you startNeed a job first?Cost to you
UA pipe trades localUA Local 13, Rochester, NYMath exam, 70%No, apply to the local$20 application fee (waivers available)
Sheet metal workers localSouthern California Sheet Metal JATCMath test plus written testNo, apply to the JATCTraining costs repaid in cash or work credits under a yearly education loan agreement
ABC chapterABC Virginia, Northern Virginia HVAC-RNone listedYes, employed in HVAC-R by a licensed contractor$2,050 member, $2,450 non-member tuition
Oregon HVAC JATCArea I HVAC JATCNo named test; algebra or placement scoresNo, ranked pool dispatched to employersNot stated
Direct hire as helperContractor job postingVaries; some use vendor tests, some noneIt is the jobNone stated

The Oregon program shows another way to rank people: its standards (revised January 2023) rank applicants on a combination of interview score and a point system, then dispatch them to employers "in ranked order from the pool of eligible applicants." ABC Virginia's program runs four years or 8,000 on-the-job hours with about 150 classroom hours a year, and classes meet weekly in the late afternoon.

Our HVAC trade school vs apprenticeship vs online training post compares costs and timelines across paths in more depth.

When do HVAC apprenticeship programs take applications?

Windows range from a few weeks to a full year, so mark your calendar early.

  • Sheet Metal Workers Local 25, Northern New Jersey: online applications ran April 6 to May 1, 2026, with documents due the same day.
  • Southern California Sheet Metal JATC: applications open the first Monday of December (Dec. 7, 2026, at 6 a.m. Pacific) and close when the maximum is received. Test notices are mailed about two weeks before testing.
  • NY sheet metal and UA locals: recruitment periods of about a year, for example April 8, 2026 to April 7, 2027 at Sheet Metal Workers Local 46.
  • Minnesota sheet metal programs: year-round, tied to getting hired by a contractor, per a state labor department page updated Oct. 2024.
  • Sheet Metal Workers Local 10: ranks applicants by aptitude test score, work experience and high school grades, then places them "in descending order of ranking" as work demands.

SMART says its training runs through 148 joint apprenticeship training committees across the U.S. and Canada, so search for the one that covers your area rather than assuming one schedule.

How do you prepare for an HVAC apprenticeship aptitude test?

Ask the program which test it uses, then train for that test. A general plan:

  1. Drill timed arithmetic and algebra. A 15-minute math test rewards speed with fractions, decimals and equations. Khan Academy's free Algebra 1 essentials course is a solid base.
  2. Practice spatial reasoning if you are applying to sheet metal. The Paper Board Test asks you to visualize objects in three dimensions, so fold paper, sketch simple duct fittings and practice reading drawings.
  3. Work on mechanical concepts for Bennett-style or mechanical comprehension sections. Our mechanical aptitude test guide walks through gears, pulleys, levers and heat.
  4. Use free official practice. ACT offers free practice tests for the WorkKeys NCRC assessments, and College Board offers free Accuplacer practice if a program uses college placement scores.
  5. Line up paperwork. Order transcripts and, in Washington, your driving abstract before the window opens.
  6. Get ready for the interview. Know why you want HVAC, show you can handle heat, heights and early starts, and mention any tool or repair work you have done.

Knowing refrigeration basics also helps in interviews. The BLS notes that the EPA requires nearly all HVAC technicians to be certified in refrigerant handling (EPA Section 608), which our EPA 608 practice test covers.

Example timeline (for illustration only): three weeks on math, two on spatial and mechanical practice, one on timed practice tests, six weeks in all.

Where do our HVAC course and the CPT fit?

Our HVAC course is self-paced and online, shown on our site as 4 to 8 weeks. It is built to help you land a first HVAC apprenticeship or entry-level job. It starts with a free introduction, then costs $499 once or four payments of $150.

What it isn't: it is not accredited, it isn't hands-on lab training, and it doesn't replace apprenticeship hours, trade school where your state requires hours, or a state license. It won't stand in for any program's entrance test either.

The Career Potential Test is our free online test of critical thinking, reading, writing and math, with a percentile score you can share by link. None of the programs above lists it as an alternative to its own test, so don't count on that. It is most useful when you go straight to contractors, since some direct hires list no test at all, and a score gives the owner one more look at your math and reading. Some will value it, others won't. The CPT is new, and we haven't published validation studies.

The BLS projects HVAC mechanic and installer jobs to grow 11% from 2025 to 2035, so programs and contractors will keep hiring.

Our recommendation: pick two or three programs near you, confirm each one's test and window, and prepare for those exact tests with free practice. At the same time, take our free HVAC introduction and the CPT so you have something to show contractors who hire helpers directly.

Frequently Asked Questions

What is on an HVAC apprenticeship test?
It depends on the program. The tests we read cover math (often up to algebra), reading, mechanical comprehension and, at sheet metal programs, 3D visualization.

Is the HVAC apprenticeship test hard?
The cutoffs vary: Southern California's sheet metal JATC asks for 8th-grade math and 35 of 45 written points, while Sheet Metal Workers Local 83 asks for 6 of 15 combined points on two Criteria tests. Preparing for your program's specific test is what matters.

Do you need a job to get into an HVAC apprenticeship?
For many non-union programs, yes. ABC Virginia requires that you work in HVAC-R, and two Minnesota sheet metal programs tie acceptance to a contractor hiring you.

Do UA HVACR apprentices take a different test than plumbers?
Not at the UA locals we read. New York locals such as Local 13 and Local 81 recruit HVAC mechanic and plumber apprentices under one notice with one test.

How long is an HVAC apprenticeship?
Usually about four years or more. ABC Virginia describes its program as four years or 8,000 hours, Oregon's Area I HVAC JATC also lists 8,000 hours, and Seattle's UA Local 32 standards (April 2024) list 10,000 hours for its HVAC-service track.

Can the Career Potential Test replace an HVAC apprenticeship test?
No. None of the programs we read accepts it in place of its own test, but contractors who hire helpers directly may look at a shared CPT score.

Show contractors your math and reading

The free Career Potential Test gives you a percentile score and a link you can send with your application.

Take the free CPT

Sources